Brass Trench Gratings

Bench Trench Gratings

banner_grate_home_brass.jpg


Lathamgrate solid brass trench gratings and frames are an economical, functional and attractive solution to exterior and interior drainage and ventilation problems.

The Lathamgrate serrated texture provides a dynamic and contemporary appearance to compliment today’s architectural designs. Unlike conventional gratings, the Lathamgrate has close centre bars, concealed welds and can be fabricated to form a radius. The Lathamgrate is available for trenches up to 300mm wide.

Lathamgrate brass trench gratings and frames offer many benefits over competing products, fabricated from steel or cast iron. Aluminium and brass gratings are lightweight and attractive.

Optional trench liners simplify installation and offer improved performance. Trench gratings are for exterior and interior use, including building entrances and wash-down areas.

The grating bars are 6.25mm wide, which combined with the serrated surface help provide pedestrian safety. The closely spaced bearing bars reduce hazards in high heels. The Lathamgrate is designed for pedestrian traffic.

For heavier applications and for block-ends, angles and radii grates contact Latham Australia before specifying.


Additional Links:

Good Design Asbra Safety Stair Treads.png
Australian-Made-Logo-Colour.jpg
Latham-Genuine-Warranty-Green-Tick-Symbol

Aluminium Serrated Top A B C Open Flow Area per lineal metre of grate (cm2) Class Classification as per AS 3996 Number of 6.5mm Serrated T's
All measurements in millimetres. 
BRGLS-3S 42mm 80mm 56mm 360 A 5
BRGLS-4S 68mm 106mm 56mm 480 A 7
BRGLS-5S 81mm 119mm 56mm 540 A 8
BRGLS-6S 107mm 145mm 56mm 660 A 10

The BRGLS Series serrated top solid brass trench grates are designed predominantly for pedestrian applications. They are commonly used in office building entrances, homes, parks, recreational harbour or beach foreshores, casinos, convention centres, exhibition centres, schools, hospitals, hotels etc.

The BRGLS Series serrated top solid brass trench grates are designed for recessed applications and should be installed to finish flush with the surrounding floor finishes. The BRGLS Series have folded 3mm brass trench liners with an overall depth of 56mm. The grate is raised off the base of the trench by 19mm high x 15mm wide welded flanges fixed to the bearing cross supports, allowing for clear water flow under the grate structure. The trench frames are supplied with welded brass strap anchors at approximately 350mm centres (fixings by others). The  solid brass self-supporting trench liner is supplied in lengths of 1800mm, complete with joining flanges for running longer lengths. The grate insert sections will be supplied in custom lengths to 4000mm and simply drop in position.

If required, factory manufactured fully welded angles and T’s are available for the grates and liners. The system is also available with block ends for the frame and trench. When the trench liner is used and factory fabricated block ends installed, the system will be an enclosed trough. Lathams can supply the BRGLS Series with welded spigots for the trench liner.

 

View and download our data sheets - PDF


Enquire About This Product

Aluminium Serrated Top B Open Flow Area per lineal metre of grate (cm2) Class Classification as per AS 3996 Number of 6.5mm Serrated T's
All measurements in millimetres. 
BRGPL-3S 75mm 300 B 4
BRGPL-4S 100mm 420 B 6
BRGPL-5S 125mm 540 B 8
BRGPL-6S 151mm 660 A 10
BRGPL-8S 204mm 900 A 14

The BRGPL Series serrated top solid brass trench grates are predominantly suitable for pedestrian applications, such as residential and commercial towers, homes, parks, recreational harbour or beach foreshores, schools, hospitals, hotels, showrooms, arenas and stadiums etc.

The BRGPL Series are removable solid grate units. They are designed to sit on a formed step or trench base and have an overall depth of 50mm. Alternatively, they can sit on levelling rods in the slab, but they must be fully supported at the ends to ensure they do not lift when traffic passes over a joint. They carry seamless welded cross supports at approximately 300mm centres. The grates can be supplied in custom lengths to 4000mm and factory manufactured fully welded angles and T’s are available.

 

View and download our data sheets - PDF

Enquire About This Product

Aluminium Serrated Top A B Open Flow Area per lineal metre of grate (cm2) Class Classification as per AS 3996 Number of 6.5mm Serrated T's
All measurements in millimetres. 
BRGNS-4S 56mm 100mm 480mm A 7
BRGNS-5S 83mm 127mm 600mm A 9
BRGNS-6S 108mm 152mm 720mm A 11
BRGNS-8S 148mm 192mm 900mm A 14

The BRGNS Series serrated top solid brass trench grates are for pedestrian applications. They are commonly used in office building entrances, home, parks, recreational harbour or beach foreshores, casinos, convention centres, exhibition centres,  schools, hospitals, hotels etc. They are designed to sit over a preformed trench and require a 36mm deep x 25mm wide bearing platform on each side of the trench. The 3mm narrow view brass frame is mechanically fixed to the bearing platforms and the edge of the frame and grate should finish level with the surrounding floor finish. The BRGNS Series are used in a range of applications both internally and externally.

The BRGNS Series is supplied with the frame that is set on a preformed bearing platforms. The grates will simply drop into the frame making for easy removal for access and cleaning. The material can be supplied in custom lengths to 4000mm for the grate inserts whilst the aluminium angle frame can be supplied in lengths to 3600mm. Factory manufactured fully welded angles and T’s are available as well as hidden locking mechanisms. The system is also available with end frame surrounds.

 

View and download our data sheets - PDF

Enquire About This Product

Aluminium Serrated Top A B Open Flow Area per lineal metre of grate (cm2) Class Classification as per AS 3996 Number of 6.5mm Serrated T's
All measurements in millimetres
BRGRS-3S 72mm 120mm 300 A 4
BRGRS-4S 97mm 145mm 420 A 6
BRGRS-5S 122mm 170mm 540 A 8
BRGRS-6S 147mm 195mm 660 A 10
BRGRS-8S 197mm 245mm 900 A 14

The BRGRS Series  serrated top solid brass trench grates are designed for surface mounted pedestrian applications. They are commonly used in office building entrances, homes, parks, recreational harbour or beach foreshores, schools, hospitals, hotels, showrooms, arenas and stadiums etc. They are also commonly used for ventilation applications, such as floor AC vent covers or as access covers to floor under deck areas that require aesthetically pleasing and trafficable solutions.

The BRGRS Series is supplied as a complete drop in unit system. It is self-supporting on the surround frames, making for easy removal for access and cleaning. The material can be supplied in custom lengths to 4000mm and factory manufactured fully welded angles and T’s are available for the surface mounted grate if required. The system is also available with end frame surrounds.

 

View and download our data sheets - PDF

Enquire About This Product

Aluminium Serrated Top A B C Unabated Clear Flow at Suppert Class Classification as per AS 3996 Number of 6.5mm Serrated T's
All measurements in millimetres. 
BRBATH-2S 18mm 56mm 50mm 16mm x 15mm A 3
BRBATH-3S 42mm 80mm 50mm 42mm x 15mm A 5
BRBATH-4S 68mm 106mm 50mm 68mm x 15mm A 7
BRBATH-6S 107mm 145mm 50mm 105mm x 15mm A 10

The Latham Grate range has now been extended to incorporate the BRBATH Series which are specifically designed for bathroom applications. The BRBATH Series incorporates fully sealed solid brass trench liners with block ends.These series are available as standard off the shelf units in the lengths and width detailed above, or in custom lengths.

As standard the external trough depth is 50mm which is usually suitable to a floor finish set down in a bathroom. Other depths are available on request.

The systems can be supplied with or without a metal spigot of the same material  extending to a depth of 100mm below the base of the trench liner for site cutting to suit.

Finishes - As standard the grates and liners are mill finish brass depending on the model selected. On request and for an additional charge the brass units can be supplied with a chromed finish. Stock standard units are available for the BRBATH-3S, BRBATH-4S in lengths of 900mm. Custom lengths can be manufactured on request. 

 

View and download our data sheets - PDF


Enquire About This Product

Have a question about your upcoming project or requirements?

form-bg.jpg